ECX Torment Bedienerhandbuch PDF herunterladen (Seite 3)

TORMENT

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with

a combination of waterproof and water-resistant components to al-

low you to operate the product in many “wet conditions,” including

puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not

completely waterproof and your vehicle should NOT be treated

like a submarine. The various electronic components used in the

vehicle, such as the Electronic Speed Control (ESC) and servo(s)

are waterproof, however, most of the mechanical components are

water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts,

as well as the contacts in the electrical cables, will be susceptible

to corrosion if additional maintenance is not performed after run-

ning in wet conditions. To maximize the long-term performance

of your vehicle and to keep the warranty intact, the procedures

described in the “Wet Conditions Maintenance” section below

must be performed regularly if you choose to run in wet conditions.

If you are not willing to perform the additional care and mainte-

nance required, then you should not operate the vehicle in those

conditions.

CAUTION: Failure to exercise caution while using this

product and complying with the following precautions

could result in product malfunction and/or void the warranty.

General Precautions

• Read through the wet conditions maintenance procedures and

make sure that you have all the tools you will need to properly

maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the

battery manufacturer before use. Do not use Li-Po batteries in

wet conditions.

• The included transmitter is not waterproof or water-resistant. If

using a different transmitter than the one included, consult your

transmitter's manual or the manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may

be present.

• Do not operate your vehicle where it could come in contact

with salt water (ocean water or water on salt-covered roads),

contaminated or polluted water. Salt water is very conductive

and highly corrosive, so use caution.

• Even minimal water contact can reduce the life of your motor if

it has not been certified as water-resistant or waterproof. If the

motor becomes excessively wet, apply very light throttle until

the water is mostly removed from the motor. Running a wet

motor at high speeds may rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor.

The additional resistance of operating in water causes excess

strain. Alter the gear ratio by using a smaller pinion or larger

spur gear. This will increase torque (and motor life) when

running in mud, deeper puddles, or any wet conditions that will

increase the load on the motor for an extended period of time.

Wet Conditions Maintenance

• Remove the battery pack(s) and dry the contacts. If you have an

air compressor or a can of compressed air, blow out any water

that may be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the

mud and dirt off with a garden hose. Avoid rinsing the bearings

and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the

vehicle and help remove any water that may have gotten into

small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts

with WD-40® solvent or any other water-displacing light oil.

Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may

continue to drip for a few hours.

• Increase the frequency of disassembly, inspection and

lubrication of the following:

• Front and rear axle hub assembly bearings.

• All transmission cases, gears and differentials.

• Motor—clean with an aerosol motor cleaner and re-oil the

bushings with lightweight motor oil.

Transmitter

Frequency 2.4GHz

Modulation DSM, DSM2, Marine

Battery AA x 4

Servo

Power Supply 4.8V~6V (shared with receiver)

Output Torque 41.66 oz (3 kg-cm)

Operating Speed 0.23sec/60 degrees of travel

Size 55.6 x 18 x 30mm

Electronic Speed Control (ESC)

Input Voltage 4.8–8.4V

Electric Capacity (FET) Forward 30 A/300 A

Electric Capacity (FET) Reverse 15 A/150 A

PWM Frequency 1kHz

BEC Voltage 5.6 V/1 A

Size 46.4 x 36.9 x 28.25mm

Weight 76 g

SPECIFICATIONS

1 2 3 4 5 6 7 8 ... 17 18

Kommentare zu diesen Handbüchern

Keine Kommentare

ECX Torment Bedienerhandbuch Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ferngesteuertes Spielzeug ECX Torment